• Visit our tractor and agricultural equipment communities:
    Ingersoll Forum Case IH Forum Combine Forum Hay Forum
    JCB Forum John Deere Forum Kubota Forum Mahindra Forum
    Massey Ferguson Talk New Holland Forum Valtra Forum Yanmar Forum
    Zetor Forum Farming Forum

New profile posts

Help Support SkidSteer Forum:

What's new New posts New media New media comments New profile posts Latest activity
S
Do you have operation temperature for a 642 bobcat with the ford motor... my temp is ranging around 170-198/200 degrees the idiot temperature puts that at right at red. Bought a new thermostat from bobcat it says 88c or 190f ... I'm starting to think someone put a wrong sending sensor in
K
Any idea where I might find a bushing, Variable speed drive sheave slide for an M-444 BobCat.? #11 in the photo

Attachments

  • IMG_3539.jpeg
    IMG_3539.jpeg
    389.9 KB · Views: 0
T
I have a 2007 t300. I have installed two new seat bar sensors but machine will work for a few minutes then lock out. Lights go off and not showing any codes. I have almost 8 volts at two of the wires going to the sensor. What else could be wrong or do I need to check? Thanks.
V
I have found enough information to get parts made for the power piece on the tiller.

Still lacking any help for finding a used planetarium for my case. Pictures and model on another request from previous time :) VBL
I
Hi Eddy,
I am looking for a WSM for my Kubota SSV65 skid steer. Do you have one that you can share? Thanks!
I
Hello. I see on the forum that you have a WSM for a Kubota SSV65. Any chance you can share it with me? Thanks!
jameslmarchetti70@gmail.c
I am new to this forum. I have a Case 1818 that always worked and today I noticed it's having some issues. The right side drive does not move as it use to. I can hear the pump trying but no luck. So What would you check to see if its a simple fix? My guess is it's a 1900 vintage with an onan 18hp engine. Any thought on this?
Y
Hi. as I look for help with few errors like code 1203 and aux override lamp flashing and the last one volt 11.4 on screen, I undestand that I have a problem with battery or alternator, so I checked the battery and it's o.k, I take the alternator (not an essy desassembly) to check and it is not working, I bring a new one, assembly all back and no errors at all, machine is working.
7
it seems that a post of how to handle, flipped equipment. might be needed, as well as attention to entire hyd sys after a failure. it aint me dude,
E
Easymoney74
I have a 2012 cat 246c and the lines going into the condenser are curoted and hydraulic fluid poured out. My question is. Can I pull the old condenser unit out and bypass the hydraulic lines?
I
Dealership replaced the o-rings and seals in the spool valve lift tilt on my 2002 773 turbo and it's still leaking, only when it's cold. When it warms up it stops leaking. It has 2030 hrs. Does anyone know how I can get a copy of the service manual?
R
Robanybody
You can get a copy from Bobcat but prepare to give them a kidney for it. There are several people on Ebay that sell manuals, either printed or on a thumb drive. I bought a thumb drive and took it to the local copy shop and they printed it and bound it pretty cheap.
X
What is the part number of the $55 part you ordered to correct your brake switch issue on your Ghel 2054?
M
hi mate. i am having the same problem with my s650 as you did with the dash lights staying on and wont start. did you ever find out the problem with yours
J
Jrmass
I ultimately ended up replacing the control module to clear the alarms. I chased every fuse and wire and it was the only thing that made sense. It fixed the issue, but there is still a gremlin that will lock the parking brake when starting. My machine always started in my scenario. I just could never get the parking brake to release. Hope this helps.
J
Jrmass
As said, the control module did fix my issue 99.9% of the time. It has only locked up three or four times since the C.M. replacement. Before that, it was nearly a worthless machine.
Top