Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Visit our tractor and agricultural equipment communities:
Ingersoll Forum
Case IH Forum
Combine Forum
Hay Forum
JCB Forum
John Deere Forum
Kubota Forum
Mahindra Forum
Massey Ferguson Talk
New Holland Forum
Valtra Forum
Yanmar Forum
Zetor Forum
Farming Forum
Forums
Other Brand Skidsteer Forums
New Holland Skidsteer Forum
looking for help , l565 boom lower pin @ quick attach broken off
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support SkidSteer Forum:
Message
<blockquote data-quote="heatpumpproducts" data-source="post: 15685" data-attributes="member: 1332"><p>on my LX565 yesterday , i was rolling down my driveway and picking up some small rocks and roots a racked out of my lawn earlier .</p><p> the boom knuckel and pin broke out at the welds it looked to be once repaired before.</p><p>so that is why i am asking for suggestions , to do it wright the second time .</p><p>now i took a look at both sides and the other side was also repaired and wraped with flate</p><p>bar welded up the boom over the hub and under the boom up the arm about 10" or so .</p><p>the problem was the pin was welded to the hub and had no way of removing it , so this is what i decided to do;</p><p>i took the parts the castle machine works , a well respected machine shop , and asked them to turn me a new hub and a pin that passes all the way through the hub , the original was</p><p>taken apart and it shouldered in the hub but did not pass all the way through .</p><p>my reassoning was so that i mite be able to remove or replace the quick attach system</p><p>at a later date if needed . now following the other side i was going to bend and weld a flat</p><p>bar over the hub up the arm and under and up the back side too.</p><p>here's my question ? after being able to look inside the arm now the side plate is only 1/4"</p><p>on both sides the top and bottom are 3/8 to 1/2" plates . what i was thinking was adding</p><p>2 plates one on either side of the hub with the inner plate bored out to allow the pin to pass through and the outer side bored out to allow for the bolt that holdes the assembly together.</p><p>would that be or is thier any recall info out thier on this subject . messicks has something called gussets and other reinforcement plates that they sell . have any other people out</p><p>thier exsperienced any other ways to fix this problem .</p></blockquote><p></p>
[QUOTE="heatpumpproducts, post: 15685, member: 1332"] on my LX565 yesterday , i was rolling down my driveway and picking up some small rocks and roots a racked out of my lawn earlier . the boom knuckel and pin broke out at the welds it looked to be once repaired before. so that is why i am asking for suggestions , to do it wright the second time . now i took a look at both sides and the other side was also repaired and wraped with flate bar welded up the boom over the hub and under the boom up the arm about 10” or so . the problem was the pin was welded to the hub and had no way of removing it , so this is what i decided to do; i took the parts the castle machine works , a well respected machine shop , and asked them to turn me a new hub and a pin that passes all the way through the hub , the original was taken apart and it shouldered in the hub but did not pass all the way through . my reassoning was so that i mite be able to remove or replace the quick attach system at a later date if needed . now following the other side i was going to bend and weld a flat bar over the hub up the arm and under and up the back side too. here's my question ? after being able to look inside the arm now the side plate is only 1/4” on both sides the top and bottom are 3/8 to 1/2” plates . what i was thinking was adding 2 plates one on either side of the hub with the inner plate bored out to allow the pin to pass through and the outer side bored out to allow for the bolt that holdes the assembly together. would that be or is thier any recall info out thier on this subject . messicks has something called gussets and other reinforcement plates that they sell . have any other people out thier exsperienced any other ways to fix this problem . [/QUOTE]
Verification
Post reply
Forums
Other Brand Skidsteer Forums
New Holland Skidsteer Forum
looking for help , l565 boom lower pin @ quick attach broken off
Top
