Visit our tractor and agricultural equipment communities:

Ingersoll Forum Case IH Forum Combine Forum Hay Forum

JCB Forum John Deere Forum Kubota Forum Mahindra Forum

Massey Ferguson Talk New Holland Forum Valtra Forum Yanmar Forum

Zetor Forum Farming Forum

Reply to thread

Help Support SkidSteer Forum:

Message: <blockquote data-quote="Mike10" data-source="post: 61079" data-attributes="member: 5461"><p>From the service manual.</p><p><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">The seat harness must have a three-inch</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">length bulge, 1. There are two resistor-type diodes in</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">the T/W wire inside this harness. These resistors cut</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">the voltage returning from the seat switch to the</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">control module by 1.2 to 1.6 volt. The control module</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">reads this voltage drop when the operator is sitting in</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">the seat, and themodule is set for the next step of the</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">start-up sequence. If the harness does not have</div></span></span></span></span></em></p><div style="text-align: left"><em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px">these diodes, the control module will not light the</div><p>SOL (solenoid) light and will not unlock the solenoid</span></span></span></span></em></p><p> <em><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"><span style="font-family: 'Helvetica-Oblique'"><span style="font-size: 10px"></span></span></span></span></em></p></blockquote><p></p>

Verification

Top