Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Bobcat Skidsteer Forums
General Bobcat Skidsteer Forum
Help with getting my 743 hopefully up and running :>
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support SkidSteer Forum:
Message
<blockquote data-quote="743needhelp" data-source="post: 80999" data-attributes="member: 11420"><p>Hey guys I have just replaced the engine in the 743 I bought and I am trying to get everything hooked back up but I need a little help and would greatly appreciate any I can get. +++++++ First off I am not mechanically inclined but have made it this far with some of your help so far but please dont make fun of me for what may be simple and stupid questions to you guys. +++++++ First I am not sure wire the fuel line with the prime bulb goes for sure on the v2203-DI ( I think it goes near where the starter is and there is an old clipped off metal tubing piece. Its the bottom where there is a medium size knob on the top of it where another line comes out the side and then goes to the little fuel bleeder valve that then has another hose that comes off it and goes to the first injector. If this is incorrect please let me know. ++++++ The second thing is the governor on these I think Antfarmer told me may need to be adjusted or I read somewhere else to just take it off the old 1702 but I am not even sure what the governor is but I think its the thing with the little adjustable screws that keep you from moving the throttle too much. ++++++ Also since I got the machine you can turn the wheels by hand but I think its just because all the hydraulic fluid was removed when the previous owners were replacing some seals which I hope they did so correctly. When I checked there was only a very small amount of fluid in the tank. I have since filled it. Is that all I need to do and when the engine is run it will bleed the hydraulics and make it where you cant turn them by hand because if I understand correctly you should not be able to freely move the machine without it running. +++++++++ Finally I need a wiring diagram to rewire everything because someone has cut wires everywhere, spliced others, and left a few taped off and hanging. I have it up on blocks as AntFarmer told me to do for safety so should I just try to jump the starter and get the engine running first or how should I proceed. Thanks, Norm</p></blockquote><p></p>
[QUOTE="743needhelp, post: 80999, member: 11420"] Hey guys I have just replaced the engine in the 743 I bought and I am trying to get everything hooked back up but I need a little help and would greatly appreciate any I can get. +++++++ First off I am not mechanically inclined but have made it this far with some of your help so far but please dont make fun of me for what may be simple and stupid questions to you guys. +++++++ First I am not sure wire the fuel line with the prime bulb goes for sure on the v2203-DI ( I think it goes near where the starter is and there is an old clipped off metal tubing piece. Its the bottom where there is a medium size knob on the top of it where another line comes out the side and then goes to the little fuel bleeder valve that then has another hose that comes off it and goes to the first injector. If this is incorrect please let me know. ++++++ The second thing is the governor on these I think Antfarmer told me may need to be adjusted or I read somewhere else to just take it off the old 1702 but I am not even sure what the governor is but I think its the thing with the little adjustable screws that keep you from moving the throttle too much. ++++++ Also since I got the machine you can turn the wheels by hand but I think its just because all the hydraulic fluid was removed when the previous owners were replacing some seals which I hope they did so correctly. When I checked there was only a very small amount of fluid in the tank. I have since filled it. Is that all I need to do and when the engine is run it will bleed the hydraulics and make it where you cant turn them by hand because if I understand correctly you should not be able to freely move the machine without it running. +++++++++ Finally I need a wiring diagram to rewire everything because someone has cut wires everywhere, spliced others, and left a few taped off and hanging. I have it up on blocks as AntFarmer told me to do for safety so should I just try to jump the starter and get the engine running first or how should I proceed. Thanks, Norm [/QUOTE]
Verification
Post reply
Forums
Bobcat Skidsteer Forums
General Bobcat Skidsteer Forum
Help with getting my 743 hopefully up and running :>
Top