Visit our tractor and agricultural equipment communities:

Ingersoll Forum Case IH Forum Combine Forum Hay Forum

JCB Forum John Deere Forum Kubota Forum Mahindra Forum

Massey Ferguson Talk New Holland Forum Valtra Forum Yanmar Forum

Zetor Forum Farming Forum

Reply to thread

Help Support SkidSteer Forum:

Message: <blockquote data-quote="Mike10" data-source="post: 68163" data-attributes="member: 5461">[FONT=Swiss721SWA,Bold][FONT=Swiss721SWA,Bold]<div style="text-align: left">I forgot to mention you need to be in the diagnostic mode to do the checks.  To get in the diagnostic mode do the following.</div><div style="text-align: left"></div><div style="text-align: left">To Enter Diagnostic Or Setup Mode:</div>[/FONT][/FONT]<div style="text-align: left">1. Lower the boom and bucket to the ground or</div><div style="text-align: left">remove any attachment and rest the boom on the</div><div style="text-align: left">boom lock pins.</div><div style="text-align: left">2. Turn .OFF. the ignition key.</div><div style="text-align: left">3. Unbuckle the seat belt, raise your weight off the</div><div style="text-align: left">seat, and wait until all EIC lights are off.</div><div style="text-align: left">4. While out of the seat, press and hold the .OPEN</div><div style="text-align: left">BOOK. switch, 2, sit in the seat and turn the</div><div style="text-align: left">ignition key to the .ON. position; Do Not engage</div><div style="text-align: left">the starter.</div><div style="text-align: left">5. Display, 3, will show the program level of the EIC</div><div style="text-align: left">board (example - r0100); at this time, release the</div><div style="text-align: left">.OPEN BOOK. switch.</div><div style="text-align: left">6. Display will show .LOC_ _. for lock.</div><div style="text-align: left">7. Press and release the .ARROW. switch, 1;</div><div style="text-align: left">.dIAg. (for Diagnostic) will appear in the</div><div style="text-align: left">character display.</div><div style="text-align: left">8. Press and release the .ARROW. switch again</div><div style="text-align: left">will move to the .SEtUP. mode in the display.</div><div style="text-align: left">Pressing and holding the .OPEN BOOK. switch</div><div style="text-align: left">when in either mode will enter the selected mode for</div>tests or changes to the EIC.[FONT=Swiss721SWA,Bold][FONT=Swiss721SWA,Bold]<div style="text-align: left">EIC Diagnostics and Setup Items</div><div style="text-align: left">Diagnostics Mode</div>  <div style="text-align: left">With display showing .LOC_ _. for lock.</div><div style="text-align: left">1. Press and release the .ARROW. switch, 1; .dIAg. will appear in the character display, 2.</div><div style="text-align: left">2. Press and hold the .OPEN BOOK. switch, 1, until a low case .d. appears in the character display,</div><div style="text-align: left">2, release the .OPEN BOOK. switch. The EIC is now in Diagnostics.</div><div style="text-align: left">Each individual monitored circuit can now be tested for proper operation.</div><div style="text-align: left">When in Diagnostics and any circuit is activated the EIC board will light all lights and an audible alarm will</div><div style="text-align: left">sound.</div><div style="text-align: left">The Diagnostic test will not verify the performance of a sensor or sender. Only the EIC board and wires to</div><div style="text-align: left">the sender or sensor are tested.</div><div style="text-align: left">The following circuits can be tested:</div><div style="text-align: left">1. EIC board bulbs</div><div style="text-align: left">2. EIC board circuits</div><div style="text-align: left">3. EIC board arrow and open book switches</div><div style="text-align: left">4. Audible beeper</div><div style="text-align: left">5. Engine air filter circuit</div><div style="text-align: left">6. Hydraulic oil filter circuit</div><div style="text-align: left">7. Hydrostatic transmission charge pressurecircuit</div><div style="text-align: left">8. Engine oil pressure circuit</div><div style="text-align: left">9. Engine Coolant temperature circuit</div><div style="text-align: left">10. Transmission/hydraulic oil temperaturecircuit</div><div style="text-align: left">11. Fuel level circuit</div><div style="text-align: left">12. Seat switch(es) and circuit</div><div style="text-align: left">13. Seat belt switch and circuit</div>14. Service/Run switchChecking Fuel Sender Circuit <div style="text-align: left">Disconnect one wire, 1, and use a jumper wire and connect sender terminal to other terminal, 2,</div><div style="text-align: left">and the EIC board will light and beep. If the EIC board lights and beeps, the EIC and circuit wires</div><div style="text-align: left">to the sender are OK. If the EIC board fails to light, check the wires to the EIC board.</div><div style="text-align: left"></div><div style="text-align: left">This procedure is a little confusing.  I think what you need to do is remove one wire from the sender and jump from that wire to the other wire still attached to the sender.</div><div style="text-align: left"> </div>  [FONT=Swiss721SWA,Bold] [FONT=Swiss721SWA,Bold] <div style="text-align: left"> </div><div style="text-align: left"> </div>[/FONT]<div style="text-align: left"> </div>      [/FONT] [/FONT][/FONT]</blockquote>

Verification