Recent content by CASE 1840

The starter drive ( bendix ) could be slipping. It is a one way clutch so when the diesel motor starts the electric starter motor does not spin to extreem speeds until you let go of the key. Another possibility is that the cranking signal between the key and starter is eratic and what you are...

I've got the motor sitting in the machine and mostly hooked up but other projects are getting done at the moment. Based on the motor mount swap, I'd say these machines were designed to take a 3 or a 4. Here is the quick run down to install a 4 where a 3 came out. Move the rear motor mounts left...

Have a look at agparts , they have rebuild kits and some aftermarket cranks. Look at 87 and up Ford / New Holland farm tractors as these use a engine very similar to the skid motor. The skid is a 332T / JF , the farm tractors use a BSD332. ( This basic engine goes back to the 60's ) Also try...

I've typed in paragraphs but sometime this board compresses everyting into one block. " I also would like to know how to get the crankshaft back in if none of the alignment marks lign up? " .. ...

" I also would like to know how to get the crankshaft back in if none of the alignment marks lign up? " .. . .. . . There will be marks on the timing gear.. . . . . " The crank was broken in 3 different places, none of the bearings show any wear, the engine still ran. Still can't understand how...

I don't have a wiring diagram for these. Find the coolant temp switch and unplug it then see if the light is still on. If if is still on _AND_ this is a system that uses a on when overheat type switch, check for a wire rubbed through to ground..

Vickers is now part of Eaton, go to their web site for a repair and parts manual online.

Before running the glow pulg directly off the battery, check the voltage printed on the hex of the plug. Many glow plugs are rated less than 12V when used on a 12 V system and giving them full power can make them burn out. The low voltage plugs will have either a controler , series resistor...

The Eaton web site has repair and parts manuals online, start there. Saying “the pump is bad” isn't much of a diagnosis from your guy. A bad cylinder block, valve plate or piston won't cause the problem you have. Seals should be a external repair. Even if the shafts are getting loose, a fresh...

These use a M46 series tandem pump from Sundstrand / Sauer , the drive motors are Danfoss OMT400. ( All of this is under the Sauer banner. ) These parts are the same model as used on a Case 1835C and 1840. ( I've got all 3 machines ) . . . . . . . . . The Sauer web site has manuals online...

Some ride on Tennant floor sweepers use the " Kent " Ford motor. ( 1.1 Liter , 1.3 and 1.6 )

I'm looking for a clear picture of the governor linkage. ( The case parts site has the linkage fragmented across a few pictures and it seems that a few parts are not shown. ) Currently I'm installing a TM27 ( Continental 4 cyl gas ) in place of a TMD20 ( 3 cyl diesel ). The 27 came out of a...

The guy that owns the 751 I looked at a while beck has not taked my offer yet ( he called once to see if I was firm ) . Will let you know if that changes.

I'm doing a TMD20 diesel 3 cylinder to TM27 gas 4 cyl. The engine was from a forklift so the governor is still there but it may need some changes. The gov might be a RPM limiter rather than a constant speed control. . . . . . In any event, the 3 and 4 cyl Continentals are built on the same...

Found this link to Continental parts ( and the TM 13 ) www.agkits.com/ford-tm13-tm20-gas-valve-lifter-continental.aspx