Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Bobcat Skidsteer Forums
General Bobcat Skidsteer Forum
T-190 Starting Problem
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support SkidSteer Forum:
Message
<blockquote data-quote="Fishfiles" data-source="post: 11895" data-attributes="member: 782"><p>No Input I say means that the controller is not communicating with the console ,it could be wiring , but I have found in the past it has taken a new controller to fix it , which has to be programmed with your hours and serial number by the dealer , but you could install it easily in 15 minutes , if you have a buddy with the same machine you can switch the controller and see if the problem goes away ----- but I have seen where when the code number to start the machine will not be accepted that mosture was the cause , when this happens if you press the code number the little asteric (*) on the screen is suppose to light each time a number is press so if you have a 4 number code 4 (*'s) will be lit up ,and if all the (*'s) are not lit it won't start , I know this is not your problem but it would not hurt to try as I have seen where you can take the console out the machine and bring it inside over night and hit it with a hair drier and it worked sometimes for the not accepting the code problem , but really feel that your problem is something else ,---------- another thing I would check is the panel in the middle of the dash which holds the brake switch which has two screws holding it in , the screw on the left side has a tendency to rub the insulation off the wiring which connects the right side console to the controller , I seen this happen a few times but never was the out come " No Input" , it was a no start when button pushed problem ----------if it isn't something easy I think the best thing for you to do with that one is probally to bring the machine to the dealer and have them check it out as you could waste a lot of time trying to find the cause , or change the controller and it is in the wiring and they don't take the controller back for credit as it is programmed to your machine and can only be scrubbed clean by the factory</p></blockquote><p></p>
[QUOTE="Fishfiles, post: 11895, member: 782"] No Input I say means that the controller is not communicating with the console ,it could be wiring , but I have found in the past it has taken a new controller to fix it , which has to be programmed with your hours and serial number by the dealer , but you could install it easily in 15 minutes , if you have a buddy with the same machine you can switch the controller and see if the problem goes away ----- but I have seen where when the code number to start the machine will not be accepted that mosture was the cause , when this happens if you press the code number the little asteric (*) on the screen is suppose to light each time a number is press so if you have a 4 number code 4 (*'s) will be lit up ,and if all the (*'s) are not lit it won't start , I know this is not your problem but it would not hurt to try as I have seen where you can take the console out the machine and bring it inside over night and hit it with a hair drier and it worked sometimes for the not accepting the code problem , but really feel that your problem is something else ,---------- another thing I would check is the panel in the middle of the dash which holds the brake switch which has two screws holding it in , the screw on the left side has a tendency to rub the insulation off the wiring which connects the right side console to the controller , I seen this happen a few times but never was the out come " No Input" , it was a no start when button pushed problem ----------if it isn't something easy I think the best thing for you to do with that one is probally to bring the machine to the dealer and have them check it out as you could waste a lot of time trying to find the cause , or change the controller and it is in the wiring and they don't take the controller back for credit as it is programmed to your machine and can only be scrubbed clean by the factory [/QUOTE]
Verification
Post reply
Forums
Bobcat Skidsteer Forums
General Bobcat Skidsteer Forum
T-190 Starting Problem
Top