Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Other Brand Skidsteer Forums
GEHL Skidsteer Forum
Gehl HL3000 input shaft Anyone know of used parts?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support SkidSteer Forum:
Message
<blockquote data-quote="XSleeper" data-source="post: 114576" data-attributes="member: 10730"><p>So during the cold snap I was clearing the driveway with my newly repowered skidsteer, and the hydraulics simply quit. SUDDENLY. Not good. Worked fine when I took it out of the garage but it didn't like the below 0 temps and quit after about 20 minutes of work. I haven't taken it apart yet, but the input shaft appears to rattle around a little as the engine idles, so it seems likely that f I take it apart I'm going to find that the input shaft and input gear are probably stripped and bearings and seals shot. I'm assuming these parts are non-existant since an internet search turns up nothing except for the 2 bearings. Parts manual: https://midtnequipment.com/content/gehl-parts-manuals/Skid-Loader/previous-models/HL3000-Skid-Loader-Parts-Manual-901939.pdf&ved=2ahUKEwjRgPTr2vzuAhVOG80KHXXiCwoQFjAAegQIARAC&usg=AOvVaw3y1e99AiRDydZ3uinclVGS The parts that I suspect of being shot are on page 8 of the parts manual: 603159 (found), 603169 and 603170. Any source for these parts? And a related question, does anyone know of a junked HL3000 that is being parted out?</p></blockquote><p></p>
[QUOTE="XSleeper, post: 114576, member: 10730"] So during the cold snap I was clearing the driveway with my newly repowered skidsteer, and the hydraulics simply quit. SUDDENLY. Not good. Worked fine when I took it out of the garage but it didn't like the below 0 temps and quit after about 20 minutes of work. I haven't taken it apart yet, but the input shaft appears to rattle around a little as the engine idles, so it seems likely that f I take it apart I'm going to find that the input shaft and input gear are probably stripped and bearings and seals shot. I'm assuming these parts are non-existant since an internet search turns up nothing except for the 2 bearings. Parts manual: https://midtnequipment.com/content/gehl-parts-manuals/Skid-Loader/previous-models/HL3000-Skid-Loader-Parts-Manual-901939.pdf&ved=2ahUKEwjRgPTr2vzuAhVOG80KHXXiCwoQFjAAegQIARAC&usg=AOvVaw3y1e99AiRDydZ3uinclVGS The parts that I suspect of being shot are on page 8 of the parts manual: 603159 (found), 603169 and 603170. Any source for these parts? And a related question, does anyone know of a junked HL3000 that is being parted out? [/QUOTE]
Verification
Post reply
Forums
Other Brand Skidsteer Forums
GEHL Skidsteer Forum
Gehl HL3000 input shaft Anyone know of used parts?
Top