The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
Hi , I need a used a 873 lift arm. Sources ? Thanks - A
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Help Support SkidSteer Forum:
antfarmer2
Well-known member
- Joined
- Oct 28, 2013
- Messages
- 2,801
Where are you?
The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
Western COWhere are you?
antfarmer2
Well-known member
- Joined
- Oct 28, 2013
- Messages
- 2,801
Call 877-530-5010 this is a big tractor scrap yard up there might be some info sorry best I could findWestern CO
The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
Didnt find one yet but thanks for the help.Call 877-530-5010 this is a big tractor scrap yard up there might be some info sorry best I could find
antfarmer2
Well-known member
- Joined
- Oct 28, 2013
- Messages
- 2,801
Found some in Mich and Indy I think but a bit far for the post manDidnt find one yet but thanks for the help.
The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
Its for a customer it would be ok to ship it probably.Found some in Mich and Indy I think but a bit far for the post man
antfarmer2
Well-known member
- Joined
- Oct 28, 2013
- Messages
- 2,801
Ok found a place in Illinois looks like they have four of them scraping out 618-833-5498Its for a customer it would be ok to ship it probably.
The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
Still need one fellas. Thanks !Ok found a place in Illinois looks like they have four of them scraping out 618-833-5498
Mikefromcny
Well-known member
- Joined
- Nov 13, 2011
- Messages
- 352
Have you tried wengers of myerstown, pa? What series is your machine, c, f, or g? betting its not a g.Still need one fellas. Thanks !
[email protected]
Well-known member
- Joined
- Feb 23, 2011
- Messages
- 878
bobcat of NH has one http://www.bobcatnh.com/pre_owned_detail.asp?sid=4618472E-02X2K4K2014J8I43I01JPMQ4501R0&veh=1710666Have you tried wengers of myerstown, pa? What series is your machine, c, f, or g? betting its not a g.
The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
Thanks guys I will check those out. I need a G series arm.bobcat of NH has one http://www.bobcatnh.com/pre_owned_detail.asp?sid=4618472E-02X2K4K2014J8I43I01JPMQ4501R0&veh=1710666
The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
Bump I still need one guys! Thanks !Thanks guys I will check those out. I need a G series arm.
If they are cracked like they always are, have a weld shop fix them.Bump I still need one guys! Thanks !
The Extractor
Member
- Joined
- Nov 22, 2013
- Messages
- 8
I am the weld shop. These are junk multiple repairs and they are bent and the rear pin holes are ripped off.If they are cracked like they always are, have a weld shop fix them.
The rear pivot points can be replaced, the bends can be fixed, but will not be easy.I am the weld shop. These are junk multiple repairs and they are bent and the rear pin holes are ripped off.
Have you thought about a lisitng on craigs list? see if anyone has leads
