Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Bobcat Skidsteer Forums
General Bobcat Skidsteer Forum
S250 non starter no ignition lights
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Help Support SkidSteer Forum:
Message
<blockquote data-quote="Suttonpark" data-source="post: 71282" data-attributes="member: 10143"><p>I spoke to the dealer, one just wants to sell me a dash console. The other wouldnt know a Bobcat if it crashed through their front door. I don't think it is a dash console as from what I can gather I should have power up to the ignition on the 1220 wire and the 1920 wire. 1000-1999 wires being battery voltage. I only have it on the 1220 wire. I've checked the 1920 wire and repaired any bad connections. I checked for 12volts out of the computer and there wasn't any. Unless this 1920 wire is from the ignition switch to the computer????? Can anyone confirm. I then checked the 1110 1120 1130 wires into the computer, these were corroded where someone had previously damaged the insulation when doing a previous repair. With these repaired there is now power in to the computer, but still nothing. I then checked the two earth wires, 2100 and 2110. However on my machine I could only find 2900 and 2110, both appear to be good. Ive gone round all the ground/earth posts and cleaned them, admittedly there maybe more but I dont know. I will not be beaten on this one and am very reluctant to buy components when I pretty sure its a wiring issue, going on the amount of repairs I've had to do already. Having found out a little more info on this machine, it has only 1063hrs in a corrosive enviroment, but apparantly sat for three-four ish years. Im unsure if its run since. The bobcat dealer who originally looked at the fault said the machine needed a new loom and computer, all this from a 10min site visit and never removed a single panel, lifted the cab or even removed the fuse cover. If this engineer is correct, I want him working for me Any help would be greatly appreciated.</p></blockquote><p></p>
[QUOTE="Suttonpark, post: 71282, member: 10143"] I spoke to the dealer, one just wants to sell me a dash console. The other wouldnt know a Bobcat if it crashed through their front door. I don't think it is a dash console as from what I can gather I should have power up to the ignition on the 1220 wire and the 1920 wire. 1000-1999 wires being battery voltage. I only have it on the 1220 wire. I've checked the 1920 wire and repaired any bad connections. I checked for 12volts out of the computer and there wasn't any. Unless this 1920 wire is from the ignition switch to the computer????? Can anyone confirm. I then checked the 1110 1120 1130 wires into the computer, these were corroded where someone had previously damaged the insulation when doing a previous repair. With these repaired there is now power in to the computer, but still nothing. I then checked the two earth wires, 2100 and 2110. However on my machine I could only find 2900 and 2110, both appear to be good. Ive gone round all the ground/earth posts and cleaned them, admittedly there maybe more but I dont know. I will not be beaten on this one and am very reluctant to buy components when I pretty sure its a wiring issue, going on the amount of repairs I've had to do already. Having found out a little more info on this machine, it has only 1063hrs in a corrosive enviroment, but apparantly sat for three-four ish years. Im unsure if its run since. The bobcat dealer who originally looked at the fault said the machine needed a new loom and computer, all this from a 10min site visit and never removed a single panel, lifted the cab or even removed the fuse cover. If this engineer is correct, I want him working for me Any help would be greatly appreciated. [/QUOTE]
Verification
Post reply
Forums
Bobcat Skidsteer Forums
General Bobcat Skidsteer Forum
S250 non starter no ignition lights
Top