Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
mocus250's latest activity
Help Support SkidSteer Forum:
M
mocus250
replied to the thread
753 runs and then dies like it out of fuel
.
Not sure if setup is same on your machine as my S250. Mine had that issue repeatedly. Fuel bulb would flatten out and sputtered after...
Mar 27, 2024
M
mocus250
added the media item
Fuel IMG_0922.jpg
to
Bobcat Skidsteer Photos
.
Mar 27, 2024
M
mocus250
replied to the thread
Bobcat s220 slow hydraulics
.
My first guess would be electrical switch/ solenoid if your lift / tilt handles are not mechanical linkage.
Mar 27, 2024
M
mocus250
replied to the thread
97 863
.
Yea It should be dry under the side cover. There should be little drain holes on each side of the chain case at the rear that would...
Mar 27, 2024
M
mocus250
replied to the thread
Life of axel seals on 763
.
Also wire, baling twine etc will eat a new seal fast. I try to look at. Axel sea area regularly when working around stuff like that.
Mar 17, 2024
M
mocus250
replied to the thread
Life of axel seals on 763
.
Bearings are First thing to check when you see leaky seal. I did rear Axel /bearing replacement on s 250 and Id do it again. The...
Mar 16, 2024
M
mocus250
replied to the thread
Fuel tank Drain plug on t300?
.
there are two plugs under the access plate, one is chain case and one is fuel tank. Prolly have do dig thru some gunk to uncover them...
Mar 7, 2024
M
mocus250
replied to the thread
Bearing number
.
I did seal Axel surface sleave on mine with Axel in place but it was just a sleave and seal kit from bobcat, it didn't have the flange...
Mar 7, 2024
M
mocus250
replied to the thread
Best fluid to run in763 bottom chain drive
.
Yeah, thats good information! I re- use old hydraulic oil or new 30 wt motor oil in mine mostly, Gearlube would probably work but...
Mar 7, 2024
M
mocus250
replied to the thread
Left drive lever not reurning to nutural
.
Its possible the linkage adjustable slotted connection slipped.? Does it keep moving in direction its stuck on after releasing lever?
Mar 7, 2024
M
mocus250
replied to the thread
Bobcat 763 drive sprocket and bracket help.
.
Check the bolt torque on Axel shafts. I had to purchase a straight ratcheting wrench to get good pull with cheater on sprocket Axel...
Mar 7, 2024
M
mocus250
replied to the thread
Where to look up info about my bobcat 743 and drive chain question?
.
If chain breaks or jumps off sprocket they cans do a lot of damage binding up inside the case and could cost more to fix. I replaced...
Mar 7, 2024
M
mocus250
replied to the thread
S185 starts and then shuts down
.
I had that issue and it was discharged battery due to fuse /relay coming out of socket below the seat causing alternator to not charge
Mar 5, 2024
M
mocus250
reacted to
haymaker's post
in the thread
Fuel shutoff
with
Like
.
This could be why you may be showing power to only 1 wire when you are not trying to crank, depending on where you are testing for power.
Mar 5, 2024
M
mocus250
replied to the thread
What are all these gauges for 2001 773
.
If you hit hammer button, then hit vitals and it gives detailed info about engine and hydraulic systems. I never use other ones.
Mar 5, 2024
Members
Top